Thread Rating:
  • 9 Vote(s) - 2.78 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Brake lights not working
#1
I think that I probably put the below thread in the wrong area really ....

http://www.berlingoforum.co.uk/showthread.php?tid=5205

Story so far....
Brakes lights not working, checked bulbs, checked the fuse (I think), so now replaced the brake pedal switch.... still nothing.... any thoughts or help please, I am stuck now!
Reply
#2
You need to check for voltage at the bulbs and the switch before going too deep, if you have voltage then maybe there is an earthing issue ???
[-] The following 1 user says Thank You to geoff for this post:
  • ron
Reply
#3
All the other lights are working from both clusters. This is a real pain, no other vehicle on the road at the min!!!
Reply
#4
Shhhhh...... Don't say I said it but at a push you could drive by day and turn the side lights on /off to simulate brake lights until you get sorted.

Did you have voltage at the bulb holder ?
Reply
#5
Need to try and get a tester on it today if I can. All the other lights at the back are working. But not been able to specifically test the brake light circuit.
Reply
#6
Hi, this any help? :thumbsup:
   
2006 2.0hdi 600 with bench seat.  Cool
Reply
#7
It's something to work with tomorrow in the snow! Need to go and get a tester tomorrow, didn't solve today. This van will be the death of me!
Reply
#8
So a little update. Confirmed voltage to the switch, switch working as can get voltage after the switch (on off as per the switch). So looks like something between the switch and the lights ... The plan is to run a new cable for the brake lights, from the switch to the lights... that should do it shouldn't it???
Reply
#9
Just a thought, seeing as the brake light circuit splits into two (left & right with separate earths) and you have replaced the lamps etc, chances are it's either a break in the feed wire or you are getting a back feed from the brake switch. Try feeding a lamp directly from the switched side of the pedal and see if it lights when pressed.
Let us know what you find. :thumbsup:
2006 2.0hdi 600 with bench seat.  Cool
Reply
#10
On my partner Van there are two connector blocks ,1 each side behind the seats which are prone to corrosion. The connectors had rotted off on mine. All the rear lights run through them.
Do as Rustscrat says then check connector blocks. I'm not sure if the berlingo multispace has them there but on the van follow the loom back from the lights and you'll find them under a plate which has 4 torx screws .
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
REAR AXCEL
Last Post: ajcommercial
Today 09:36 PM
» Replies: 3
» Views: 68
Odd Issues with Rear Door Sensor
Last Post: dumdum
Today 09:25 PM
» Replies: 1
» Views: 49
display fading (MFD B, not bulb related)
Last Post: sks01773
Today 07:50 PM
» Replies: 42
» Views: 6120
Are Mud Flaps the Answer ?
Last Post: iscom
Today 07:10 PM
» Replies: 4
» Views: 175
Head Light Bulbs
Last Post: dargoion
Today 05:52 PM
» Replies: 33
» Views: 999
radio code
Last Post: Tomcat3
Today 02:32 PM
» Replies: 3
» Views: 85
Sop the seatbelt buckle sitting soo low?/aux ste...
Last Post: Trevor
Today 02:13 PM
» Replies: 2
» Views: 50
Removing the rear roof storage bin (mk3 modutop)
Last Post: iscom
Today 01:31 PM
» Replies: 15
» Views: 6746
New Berlingo Auto Box - Anyone have one?
Last Post: doofer
Today 12:13 PM
» Replies: 4
» Views: 251
Help needed have immobiliser fault and fan probl...
Last Post: brajomobil
Today 12:07 PM
» Replies: 1
» Views: 66

[-]
Recent Visitors
Locations of visitors to this page