Thread Rating:
  • 16 Vote(s) - 3.13 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Engine/Immobiliser Wiring 1.4 Petrol Pre-Mux
#1
Hi, this is initially a request for help - quite likely from Rustscrat - and is part of the engine swap plan.

What I'm seeking, is the pre-multiplex wiring for a 1.4 petrol (KFX) with chipped key, including ECU and immobiliser details.

I'll be splicing in elements of the Xantia "faisceau de cablage" to use the Xantia Texton box, rather than the chancer's unlock method of unplugging it while running on a car.

We are within about ten days of the physical swap starting.

Cheers, Adam.
Reply
#2
These any good Addo ?

[Image: hvxixv.png]

[Image: v83l1h.png]
2006 2.0hdi 600 with bench seat.  Cool
[-] The following 3 users say Thank You to Rustscrat for this post:
  • addo, Ol'Jeffers, ron
Reply
#3
Fantastic! That is the only immobiliser diagram I've seen which relates well. My 605 wiring diagrams are quite different there.

The ECU pinouts are very different between KFX and RFV as well. Many thanks.
Reply
#4
Great addo!! So pleased that Rustscrat has been able to sort it out for you!!
Hey if you send me a case of VB I'll errm make sure it gets to him!!
The Older I get the Better I Was!  Cool
Reply
#5
I'd probably have to make it two cases. It's a four hour drive each way between you blokes and unless you're on the wagon I don't think it's possible to drive that long looking at a slab without cracking...
[-] The following 3 users say Thank You to addo for this post:
  • Ol'Jeffers, ron, Rustscrat
Reply
#6
Another bump mainly to thank Rustscrat; the swap is well underway and the immo diagram above is worth a mint. I'll repeat this detail elsewhere, but for the sake of convenience the M49 (pre multiplex) immobiliser box is more or less behind the headlight dipping roller switch, to the steering column right side.
[-] The following 1 user says Thank You to addo for this post:
  • Rustscrat
Reply
#7
(19-06-2013, 09:58 AM)addo Wrote:  Another bump mainly to thank Rustscrat; the swap is well underway and the immo diagram above is worth a mint. I'll repeat this detail elsewhere, but for the sake of convenience the M49 (pre multiplex) immobiliser box is more or less behind the headlight dipping roller switch, to the steering column right side.

Cheers Addo, keep us informed.:thumbsup:
2006 2.0hdi 600 with bench seat.  Cool
Reply
#8
Picked up an odd wire not in the diagrams.

8631, it's off the 16-way plug originally for the immobiliser box. I'm guessing it interfaces with the central locking box, by it's first two digits. Obviously not essential to operation, but inquisitiveness gets me every time.

Everything else inside the dash is spliced in. There's even an 820 wire in the immo harness, not shown on the schematic above - very handy.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Newbie
Last Post: Jed Clampit
Today 12:23 AM
» Replies: 3
» Views: 50
Tyre Change...old on front new on back
Last Post: RocketVANman
Yesterday 11:32 PM
» Replies: 5
» Views: 64
Finally a B9 Haynes Manual
Last Post: Satellitemark
Yesterday 08:26 PM
» Replies: 33
» Views: 2218
Fuel rail pipe replacement
Last Post: Peter Palmer
Yesterday 08:19 PM
» Replies: 2
» Views: 43
REAR AXCEL
Last Post: Tomcat3
Yesterday 07:31 PM
» Replies: 5
» Views: 131
Berlingo B9 2008 Just Testing The Water
Last Post: nickyboy4
Yesterday 06:34 PM
» Replies: 0
» Views: 32
Starting issues
Last Post: technique1966
Yesterday 06:00 PM
» Replies: 0
» Views: 29
Insurance cost
Last Post: jonny705
Yesterday 05:33 PM
» Replies: 0
» Views: 36
Are Mud Flaps the Answer ?
Last Post: Top drive
Yesterday 04:02 PM
» Replies: 11
» Views: 317
Is anyone buying a new car AFTER April 2017?
Last Post: Solent
Yesterday 03:35 PM
» Replies: 1
» Views: 53

[-]
Recent Visitors
Locations of visitors to this page