Thread Rating:
  • 24 Vote(s) - 3.13 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[How To] replace front brake pads on M59 (Mk2)
#1
1. Removing
Untighten the wheel screws.
Lift and support the front of the vehicle.
Remove the front wheels.

[Image: pads1.png]

Push the piston back (levering at a).
Check the brake fluid level.
Remove bolts (1).

[Image: pads2.png]

Tilt the brake caliper (3).
Remove the brake pads (4).
2. Cleaning

URGENT : Do not use compressed air to clean the brakes

2.1. 1st possibility
Clean the disc and the brake caliper using a recommended brake cleaning product.
Allow to dry and to drain.
Wipe with a paper towel.
2.2. 2nd possibility
Use an approved dedusting instrument (refer to the Material and Equipment Catalogue).
Visually check :
The seal around the piston
That the protective gaiters are in good condition and correctly adjusted
The wear of the brake disc
3. Refitting
Refit new brake pads.
Tilt the caliper (3) on its support.
Refit screw (1), Tighten the bolt to 3 ± 0,3 daN.m.
Refit the front wheels.
Refit the wheel screws.
Apply the brakes, with the engine running, several times before driving the vehicle.
Return the vehicle to its wheels.
Tighten the wheel bolts to 9 ± 1 da.Nm.
[-] The following 4 users say Thank You to pk7478 for this post:
  • jimbo, johngeir, ron, timduk
Reply
#2
nice one
[-] The following 1 user says Thank You to jimbo for this post:
  • j90xxx
Reply
#3
(12-02-2011, 04:36 PM)pk7478 Wrote:  1. Removing
Untighten the wheel screws.
Lift and support the front of the vehicle.
Remove the front wheels.

[Image: pads1.png]

Push the piston back (levering at a).
Check the brake fluid level.
Remove bolts (1).

[Image: pads2.png]

Tilt the brake caliper (3).
Remove the brake pads (4).
2. Cleaning

URGENT : Do not use compressed air to clean the brakes

2.1. 1st possibility
Clean the disc and the brake caliper using a recommended brake cleaning product.
Allow to dry and to drain.
Wipe with a paper towel.
2.2. 2nd possibility
Use an approved dedusting instrument (refer to the Material and Equipment Catalogue).
Visually check :
The seal around the piston
That the protective gaiters are in good condition and correctly adjusted
The wear of the brake disc
3. Refitting
Refit new brake pads.
Tilt the caliper (3) on its support.
Refit screw (1), Tighten the bolt to 3 ± 0,3 daN.m.
Refit the front wheels.
Refit the wheel screws.
Apply the brakes, with the engine running, several times before driving the vehicle.
Return the vehicle to its wheels.
Tighten the wheel bolts to 9 ± 1 da.Nm.

All good,but I use copaslip to prevent siezure/squealing on pad backs & calliper slide.Rolleyes
Strawberry flavoured windows  Dodgy
Reply
#4
Haynes recommends replacing the bolts (1).

Does anyone do this - and why ?
'98 D 800 van Big Grin
Reply
#5
Just replaced all brakes and discs on my mates mondeo, rear pads came with two new bolts for caliper, front did not!

The went in the bin Tongue
Somedays you're the pigeon, Somedays you're the statue.
Reply
#6
thanks PK, changed the pads in a half hour today,what a doddle
03 1.9DLX van
Reply
#7
Pads should come with replacement bolts that have thread locking compound on them.

Peter
Reply
#8
Just about to do this job. always good to see another explaination. Thank you.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
BULBS!!
Last Post: Jed Clampit
Yesterday 11:05 PM
» Replies: 17
» Views: 551
Finally a B9 Haynes Manual
Last Post: Satellitemark
Yesterday 10:43 PM
» Replies: 39
» Views: 2471
clunking noise
Last Post: Silverberlingo
Yesterday 10:35 PM
» Replies: 4
» Views: 64
TRAILER WANTED
Last Post: Silverberlingo
Yesterday 10:29 PM
» Replies: 4
» Views: 75
longitudinal roof rails
Last Post: Chrisville
Yesterday 10:27 PM
» Replies: 0
» Views: 18
Head Light Bulbs
Last Post: Hughzie
Yesterday 09:23 PM
» Replies: 36
» Views: 1134
Newbie
Last Post: Jed Clampit
Yesterday 08:37 PM
» Replies: 6
» Views: 87
first time ctroen owner
Last Post: Jed Clampit
Yesterday 08:25 PM
» Replies: 1
» Views: 37
M59 Cooling system change PDF
Last Post: coatess
Yesterday 06:46 PM
» Replies: 1
» Views: 210
What to look for when buying?
Last Post: polar
Yesterday 06:16 PM
» Replies: 6
» Views: 78

[-]
Recent Visitors
Locations of visitors to this page