Thread Rating:
  • 7 Vote(s) - 3.14 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Lazing on a Sunny Afternoon...
OK, here's where I'm at:

[Image: dme9.jpg]


I've removed all the clips I can feel around the aircon evaporator, but the halves still won't split. What am I missing - it feels well stuck around the TX area?

This was done because the carpet was filthy, saturated with coffees and antifreeze, also the passenger side was wringing wet underneath and clearly had been for a long time. Carpets are all scrubbed and hosed off now, resting on my panel horses.

I sincerely hope not to do another one anytime soon. This is old school car building, putting in the carpet first.
Do you have a decent inspection mirror with light?
Don't have anything that will give meaningful images there. It's quite restricted between the firewall and plastic box.
A decent boroscope isn't too expensive these days.
Mine has a 6mm camera diameter...

It has come in handy several times.

Just don't carry one and a cordless drill while walking near a women's locker room...
I should get one; there's a Snap-On borescope at one workplace but it eats batteries, so is seldom used. Might borrow it for this job.

Never been into voyeurism really; not much point in looking at things you probably can't ever play with.
[-] The following 2 users say Thank You to addo for this post:
  • RolyG, ron
OK, the answer is: Two hidden clips of the same type.

On a Haynes spanner rating, this is 3½ spanners plus a large bag of epithets. Assumed you have already removed the dash and split off the heater chamber.

Step 1: Remove the blower motor (three screws) - unplug the drain tube from it
Step 2: Unscrew the pollen filter cover (three screws) and remove the filter
Step 3: Remove the firewall through nut and washers (one metal, one fibre)
Step 4: Remove the cold air intake mesh from the scuttle (one 8mm head self-tapping bolt)
Step 5: Remove the cold air intake duct from the box top (four screws)
Step 6: Pull the box into the car far as you dare and disconnect the drain hose from the box (Clic clip)
Step 7: Identify and prise outwards from the bottom lip, all detectable spring clips
Step 8: Push the TX valve sealing foam towards the firewall far as you can
Step 9: Use a small flatblade screwdriver to flick out the last two clips previously covered by the foam

You can now separate the case halves and remove them from the vehicle, leaving the AC intact.
See! There ya go, Addo it was a five minute job after all! :twisted:
The Older I get the Better I Was!  Cool
[-] The following 1 user says Thank You to Ol'Jeffers for this post:
  • addo
About four hours including dash out, first try. Reckon I could shave 90 minutes off it another time, meaning in'n'out with a scrub-up would be a £400 job with pollen filter, coolant flush and bleed. You'd probably throw in a new matrix "while you're at it".

Forum Jump:

Users browsing this thread: 1 Guest(s)
You have to register before you can post on our site.



(Advanced Search)

Latest Threads
glow plugs
Last Post: z1000pete
Today 10:21 AM
» Replies: 0
» Views: 5
You should have listened about facebook.
Last Post: poonamjs143
Today 10:11 AM
» Replies: 0
» Views: 12
Next gen berlingo multispace
Last Post: churmy
Today 09:42 AM
» Replies: 4
» Views: 63
Is anyone buying a new car AFTER April 2017?
Last Post: doofer
Today 09:10 AM
» Replies: 12
» Views: 220
Sop the seatbelt buckle sitting soo low?/aux ste...
Last Post: Hora
Today 07:04 AM
» Replies: 5
» Views: 152
Fuel rail pipe replacement
Last Post: polar
Today 06:54 AM
» Replies: 4
» Views: 99
600lx or 800lx
Last Post: dumdum
Yesterday 11:12 PM
» Replies: 1
» Views: 45
Advise please on known problem tyre scrubbing
Last Post: shncoe1
Yesterday 10:12 PM
» Replies: 19
» Views: 1559
Another seat belt question
Last Post: berreke
Yesterday 09:02 PM
» Replies: 1
» Views: 50
hi all
Last Post: Jed Clampit
Yesterday 08:39 PM
» Replies: 2
» Views: 53

Recent Visitors
Locations of visitors to this page