Posts: 1,906
Threads: 50
Thanks Received: 475 in 420 posts
Thanks Given: 743
Joined: Jun 2011
Location: Aylesford, Kent
Reputation:
3
06-02-2015, 08:51 PM
'Kay guys I need a wiring harness diagram which shows all of the connector plugs for the external temperature sensor.
I've changed the sensor (thermistor) and the displayed temperature is all over the place as it was before the change. Occasionally it will display
the correct outside air temperature and suddenly the temperature will begin to drop. OR the display will show minus 39 degrees
and very slowly climb to a realistic value. This sounds to me like one of the loom connectors is contaminated by corrosion.
Normally I would PM Rustscrat for this but he seems to have disappeared along with Addo so if anyone can help I would be eternally
grateful.
The Older I get the Better I Was!
•
Posts: 993
Threads: 23
Thanks Received: 231 in 198 posts
Thanks Given: 46
Joined: Nov 2011
Location: N/W Kent
Reputation:
5
07-02-2015, 10:03 AM
(This post was last modified: 07-02-2015, 10:05 AM by Trevor.)
Hi OJ afraid all I can find is a note that says to make sure the connection wires close to the sensor are insulated after fitting, no use at all.
Have you tried Emailing Rustscrat, I think that can be done from this site?
--------------------------------------------------------------
2012 Iron Grey XTR 110 with lots of bits and bobs.
•
Posts: 1,906
Threads: 50
Thanks Received: 475 in 420 posts
Thanks Given: 743
Joined: Jun 2011
Location: Aylesford, Kent
Reputation:
3
All I can do Trevor is to PM him, which I have done.....how would I email him?
The Older I get the Better I Was!
•
Posts: 993
Threads: 23
Thanks Received: 231 in 198 posts
Thanks Given: 46
Joined: Nov 2011
Location: N/W Kent
Reputation:
5
I don't know, all I can see that some messages have :-
At the bottom....
--------------------------------------------------------------
2012 Iron Grey XTR 110 with lots of bits and bobs.
•
Posts: 834
Threads: 40
Thanks Received: 125 in 102 posts
Thanks Given: 82
Joined: Oct 2010
Location: Gillingham, Kent
Reputation:
6
(08-02-2015, 08:41 AM)Tomcat3 Wrote: Hi OL`jeffers try this http://www.berlingoforum.co.uk/user-1418.html
scroll to the bottom of his profile and click on the link to send a private message.
I don't think he comes on here much now, as his last visit was September. You can't email him via the forum as he hasn't checked that option in his profile.
Now an ex Berlingo owner, I have a C4
2010 (B9) Berlingo Multispace XTR HDi 112 - Kyanos Blue
Previously - 2002 (M49) Berlingo Multispace 2.0 HDi Diesel - Arctic Steel
•
Posts: 1,906
Threads: 50
Thanks Received: 475 in 420 posts
Thanks Given: 743
Joined: Jun 2011
Location: Aylesford, Kent
Reputation:
3
08-02-2015, 03:28 PM
(This post was last modified: 08-02-2015, 03:31 PM by Ol'Jeffers.)
I fired off a PM, but as Mike says he hasn't been here for a while.
I also contacted Lighty via his website but I don't think he's read the message yet.
It's not that important but it's sort of annoying to get an Ice Warning in August!!
@TC3...tried that link but I don't have the required permission...
The Older I get the Better I Was!
•