Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Opinions on Rusty Sill
#1
Shocked 
TL;DR: help, what do?

This was a nice surprise I had waiting for me when I came back to the passenger side of my car today. This certainly crept up on me, I was under the impression my bingo was largely rust-free. I don't know what caused it to just... burst all of a sudden, but it seems it has. I haven't been offroading, hopping kerbs etc..

I did hit a rather large roadside puddle the other day, is it possible that that could have somehow blown this out?

If you could all make comforting, non-expensive noises about how easy this is to fix, that'd be appreciated, Financially speaking I don't need this right now.

That said, what are my options here? Replacement sill? Weld in a patch? Have the car crushed and set my wallet on fire?

Any insight would be appreciated.

Thanks,
Tom

[Image: VnOAg1f.jpg]
Strip thread and back off 1/4 turn.
2001 (Mk1) Multispace Forte 1.9D
Reply
#2
Cut out a strip 1" wide x whatever long and weld in new metal, preferably pre galvanised steel. It will come back so budget on more work in another year.
[-] The following 1 user says Thank You to geoff for this post:
  • Tango91
Reply
#3
If you are going to keep it get the sill replaced if not as geoff says just weld it up for another year.

Just out of curiosity what year is your berlingo?
Reply
#4
Looks like it's rotted from the inside. If you have the side doors the the water comes in from the lower runner. Check that there are not any drain holes blocked along the bottom seam. Also check under your carpets and see if  they are wet. Cool
2006 2.0hdi 600 with bench seat.  Cool
Reply
#5
The trouble with welding is that the rust always come back ( been there before ) so in a sense it is better to cut out the rust until you get back to clean metal and set new metal back in ( butt weld rather than overlapping as the rust comes back quicker ) so that you can still cut back further for the next years MOT and weld more new metal back in. This way you can squeeze a few more years out of the vehicle. Once you cut back for complete sills you are going deeper into the structural side of things and the next repair is even harder and more expensive.

You have more life left in the vehicle in all likelihood but better to get the wallet set for the next wagon in due course.

If you can weld then all is much cheaper if not get a price from a back street garage - don't go to a shiny place !

edit : If you can squirt waxoyl into the sills after welding it will last longer .... if cash is tight then squirt waste engine oil into the sills, rusty cars never rust where there is an oil leak.
Reply
#6
Are you near the sea ? I've done a few like that on Fiestas, Micras, and Polos but not a Berlingo. It's not a big job and can be done to look invisible and reasonably permanent with a patch cut out and butt welded in and sealed from the back as Geoff says or bodged with a plate over the top just for a quick MOT pass. A complete sill to reveal and fix all the horrors behind it would be the expensive option. If you start tapping round it and prodding with a screwdriver you will see how far the damage really goes but I would knock the sharp edge back in and put something over it if you are still using the car (gaffer tape and a bit of filler is the quickest) just to save any personal damage.
So where does this bit go then ?
Reply
#7
http://www.autocrashparts.co.uk/citroen-...rYmglmYPao
Have a look at this.
Griff
Landmark
Ex 1.4 Berlingo Multispace
Reply
#8
(06-02-2016, 05:01 PM)Landmark Wrote:  http://www.autocrashparts.co.uk/citroen-...rYmglmYPao
Have a look at this.
Griff

£30.34 to buy a sill, £200 to fit it another £200 to paint it. Cutting a sill off and tidying up then fitting the new one is a long job if it's done properly and there is quite a lot of work involved, even more so with a sliding rear door gear to contend with so it could end up costing even more on an hourly basis at a garage.
So where does this bit go then ?
Reply
#9
I had this done on my 1999 model two years ago, and it ended up costing me 12000NOK, about £960 with todays exchange rate.(Part was about 1300NOK, or about £100, but it was a genuine Citroën part.)
That panels is a real pain to replace, so yeah, the hours fly past. That also included a pro paintjob where they matched colours to the old paint, not just matching the paint code.
Of course, things are more expensive here in Norway, but still... expect it to cost.

Also, note that I didn't have a choice. It had failed the MOT on rust, and wouldn't be accepted without papers showing that it had been done properly.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Next gen berlingo multispace
Last Post: churmy
Today 04:58 PM
» Replies: 7
» Views: 101
New Berlingo Auto Box - Anyone have one?
Last Post: Capelbond
Today 04:10 PM
» Replies: 9
» Views: 351
Newbie
Last Post: Onall4
Today 03:16 PM
» Replies: 0
» Views: 17
Finally a B9 Haynes Manual
Last Post: Satellitemark
Today 02:32 PM
» Replies: 37
» Views: 2392
glow plugs
Last Post: z1000pete
Today 10:21 AM
» Replies: 0
» Views: 27
Is anyone buying a new car AFTER April 2017?
Last Post: doofer
Today 09:10 AM
» Replies: 12
» Views: 226
Sop the seatbelt buckle sitting soo low?/aux ste...
Last Post: Hora
Today 07:04 AM
» Replies: 5
» Views: 156
Fuel rail pipe replacement
Last Post: polar
Today 06:54 AM
» Replies: 4
» Views: 102
600lx or 800lx
Last Post: dumdum
Yesterday 11:12 PM
» Replies: 1
» Views: 48
Advise please on known problem tyre scrubbing
Last Post: shncoe1
Yesterday 10:12 PM
» Replies: 19
» Views: 1572

[-]
Recent Visitors
Locations of visitors to this page