Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Over compression?
#1
Yeah, it's me and my 1.4i again...

After the oil-change and sump cleanout, I've only driven Shorter trips to the store and such(Don't like unnecessary driving. It's expensive... )

Anyway, on friday I had to drive to work instead of taking the bus, and this time it heated up to the '3/4' mark and hovered there, With an occasional Climb a mm or so higher. Of course, the heater was running at full blast because of yeah, Winter...

It was also feeling 'not right' With regards to Power in 5th gir, so when I got back home I pulled the plugs and ran a compression test.
This time I used a 'quality' gauge I borrowed from a friend(mine is 'buried' somewhere in my garage.) and instead of hitting around 10Bar, it showed 12Bar compression. 20% higher than it's supposed to be.

So, my 'el cheapo' gauge may be slightly off...
And high compression may explain the 'not right' feeling, I expect With hesitation and lack of grunt.
But can it also explain it running hot?

Today I'll go over the cams and check the clearances.
(I thought I did a decent job of that earlier. There wasn't that much carbon buildup, either, and cleaned it up pretty well when I did the headgasket)
Reply
#2
Your high comp figure shows the valves are sealing so clearances are within tolerance.2 bars up is OK just shows all is working well. Some engines seem to have better parts match than usual & work better as a result.:thumbsup:
Strawberry flavoured windows  Dodgy
Reply
#3
Count your blessings as many with a lesser compression reading would give their coil packs for 12 Bar.

The higher the compression ratio the higher the thermal efficiency of the engine and the greater the " bang per buck " as the saying goes so no it will not account for your running issues.

Head gasket and other works done ... Hmmmm.....now that would be a candidate and worthy of a double check.

I'd check your valve timing just in case it is not correct and also the valve clearances, at least it is cheap and without much to dismantle.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Tyre Change...old on front new on back
Last Post: Top drive
Today 07:13 AM
» Replies: 6
» Views: 80
Newbie
Last Post: Jed Clampit
Today 12:23 AM
» Replies: 3
» Views: 57
Finally a B9 Haynes Manual
Last Post: Satellitemark
Yesterday 08:26 PM
» Replies: 33
» Views: 2230
Fuel rail pipe replacement
Last Post: Peter Palmer
Yesterday 08:19 PM
» Replies: 2
» Views: 48
REAR AXCEL
Last Post: Tomcat3
Yesterday 07:31 PM
» Replies: 5
» Views: 138
Berlingo B9 2008 Just Testing The Water
Last Post: nickyboy4
Yesterday 06:34 PM
» Replies: 0
» Views: 37
Starting issues
Last Post: technique1966
Yesterday 06:00 PM
» Replies: 0
» Views: 35
Insurance cost
Last Post: jonny705
Yesterday 05:33 PM
» Replies: 0
» Views: 41
Are Mud Flaps the Answer ?
Last Post: Top drive
Yesterday 04:02 PM
» Replies: 11
» Views: 322
Is anyone buying a new car AFTER April 2017?
Last Post: Solent
Yesterday 03:35 PM
» Replies: 1
» Views: 60

[-]
Recent Visitors
Locations of visitors to this page