Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rear Wiper Motor
#1
Can anyone kindly advise where I can get a new 3 pin connector for a new rear screen wiper motor i need to fit in the next couple of weeks (Old unit no longer working and had to purchase a newer unit to fit)  The old wiper motor had a red 4 pin connector which will have to be changed which I'm sure I can do if it isn't too complex! The vehicle out of interest is an early 2002  Peugeot Partner Quicksilver and the new wiper motor is probably for the later MK 2 and is all that is available new now.
Reply
#2
You could use something like this http://www.ebay.co.uk/itm/3-WAY-PRE-WIRE...SwEetWAwgR
Just cut your miss matched connectors off and solder in each lead.
Are we there yet????? No we fecking ain`t  gggggrrrrrrr
Ex 1.6hdi van now 3 seater 1.4 multispace
Reply
#3
(09-05-2016, 06:27 PM)Tomcat3 Wrote:  You could use something like this http://www.ebay.co.uk/itm/3-WAY-PRE-WIRE...SwEetWAwgR
Just cut your miss matched connectors off and solder in each
Problem is that the femail connector on the new wiper motor is moulded into the unit unlike the old unit which could have been cut and new connectors soldered on - so the new male connector has to match the femail on the new wiper motor???? It is finding out where to obtain a new connector to mate with the Bosch wiper unit.
Reply
#4
Can you post a picture on here so we know what its got to look like. Probably your best bet is at your local breakers and cut one off a scrap car.
Are we there yet????? No we fecking ain`t  gggggrrrrrrr
Ex 1.6hdi van now 3 seater 1.4 multispace
Reply
#5
(09-05-2016, 07:55 PM)Tomcat3 Wrote:  Can you post a picture on here so we know what its got to look like. Probably your best bet is at your local breakers and cut one off a scrap car.
All of the scrap yards around here closed several years ago due to Health & Safety and they are replaced with dismantlers who sell bits and bobs over the counter that they have removed themselves.  New unit like the old one is a genuine Bosch unit but the 12v 3 pin connector is built into the unit rathe than on the old unit which was on the end of about 6" of cable! Could have cut and replaced with new connectors as you described from E-Bay but now it isn't that simple...shucks....


Attached Files Thumbnail(s)
       
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Newbie
Last Post: Onall4
Today 07:29 PM
» Replies: 5
» Views: 77
TRAILER WANTED
Last Post: Tomcat3
Today 07:15 PM
» Replies: 3
» Views: 57
M59 Cooling system change PDF
Last Post: coatess
Today 06:46 PM
» Replies: 1
» Views: 200
What to look for when buying?
Last Post: polar
Today 06:16 PM
» Replies: 6
» Views: 62
clunking noise
Last Post: polar
Today 06:13 PM
» Replies: 3
» Views: 44
Next gen berlingo multispace
Last Post: doofer
Today 05:55 PM
» Replies: 9
» Views: 163
first time ctroen owner
Last Post: covenanter
Today 04:43 PM
» Replies: 0
» Views: 20
brake warning light
Last Post: my mucker
Today 03:05 PM
» Replies: 1
» Views: 49
Not a Berlingo but very intresting
Last Post: Mrleadfoot
Today 02:43 PM
» Replies: 0
» Views: 42
Boot box dimensions?
Last Post: Mrleadfoot
Today 02:29 PM
» Replies: 1
» Views: 199

[-]
Recent Visitors
Locations of visitors to this page