Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[Transmission] so, i guess my clutch needs replaced?
#1


Reply
#2
Had mine done about 3 months ago, sounded exactly the same. Its the release bearing, which has a plastic centre that slides on a tube on the main shaft (Great idea Peugeot). When it wears it runs hot and breaks up the plastic which will eventually jam the bearing on the tube and leave you stranded. Better done sooner rather than later, you've got about 100 miles left on it when it starts squealing like a piggy.

[Image: 356b6755ab9d00433eb59de75e2dd32f.jpg]

Tom


Sent from my Potato using Tapatalk
Reply
#3
(14-08-2016, 07:25 AM)tomoguchi Wrote:  Had mine done about 3 months ago, sounded exactly the same. Its the release bearing, which has a plastic centre that slides on a tube on the main shaft (Great idea Peugeot).
Tom

It's not a Peugeot idea, lots of manufacturers use the same method, how many miles has the clutch done and is it slipping or has it been done before ? I have seen clutches where the diaphragm fingers have worn and broken through because the wrong release bearing has been installed and made noises like that is doing. Unless you've had the car from new and you know the full history it is hard to pinpoint from a noise.
So where does this bit go then ?
Reply
#4
(14-08-2016, 07:25 AM)tomoguchi Wrote:  Had mine done about 3 months ago, sounded exactly the same. Its the release bearing, which has a plastic centre that slides on a tube on the main shaft (Great idea Peugeot). When it wears it runs hot and breaks up the plastic which will eventually jam the bearing on the tube and leave you stranded. Better done sooner rather than later, you've got about 100 miles left on it when it starts squealing like a piggy.

[Image: 356b6755ab9d00433eb59de75e2dd32f.jpg]

Tom


Sent from my Potato using Tapatalk


Dont know if this is what happened, but it started squealing tonight and stranded me about 5 minutes from home! Have work at 0630 so it's parked up for the night and will hopefully get a recovery agent to it in teh morning and up to the garage. I definately didn't get 100 miles aftr it started squealing! more like 5!

van has 106k on it and I thought it got a new clutch at 80k but im not sure since this has happened, pretty sure the flywheel has gone too and it needs a new tming belet because again im not sure it's been done so going to be exxpensive but if i get it to 200,000 then i'll get my money worth out of it....
Reply
#5
Damn that's bad luck mic, sorry to hear it. I'd be very surprised if it isn't the release bearing! As a guideline I can say that an LUK/Borg & Beck clutch kit is about £65, input shaft sleeve/seal was £12 and it cost £180 cash for my local garage to fit it. Hope you get sorted soon!


Sent from my Potato using Tapatalk
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Berlingo 2007 1.6 hdi - intermittent sticky acce...
Last Post: Vossy1
Yesterday 04:37 PM
» Replies: 6
» Views: 306
Battery upgrade
Last Post: evdama
Yesterday 03:58 PM
» Replies: 0
» Views: 49
Wanted: 2003 M59 steering rack
Last Post: evdama
Yesterday 12:45 PM
» Replies: 1
» Views: 38
roof rack with slats
Last Post: BigVtwin996
Yesterday 09:22 AM
» Replies: 2
» Views: 158
M59 Throttle pedal
Last Post: Romahomepete
Yesterday 07:32 AM
» Replies: 4
» Views: 153
Fault Code B0079 Airbag
Last Post: Cumbrian
26-03-2024 03:06 PM
» Replies: 1
» Views: 195
Timing pin sets
Last Post: evdama
26-03-2024 11:50 AM
» Replies: 10
» Views: 265
injector plastic neck broken
Last Post: magoo1
25-03-2024 05:15 PM
» Replies: 7
» Views: 123
Multispace Forte for sale
Last Post: ffrenchie
25-03-2024 01:58 PM
» Replies: 1
» Views: 115
Spare wheel
Last Post: chrisl
24-03-2024 09:18 PM
» Replies: 17
» Views: 2042

[-]
Recent Visitors
Locations of visitors to this page

[-]
Hosting by

QuickHostUK