Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rear Wiper Motor
#1
Can anyone kindly advise where I can get a new 3 pin connector for a new rear screen wiper motor i need to fit in the next couple of weeks (Old unit no longer working and had to purchase a newer unit to fit)  The old wiper motor had a red 4 pin connector which will have to be changed which I'm sure I can do if it isn't too complex! The vehicle out of interest is an early 2002  Peugeot Partner Quicksilver and the new wiper motor is probably for the later MK 2 and is all that is available new now.
Reply
#2
You could use something like this http://www.ebay.co.uk/itm/3-WAY-PRE-WIRE...SwEetWAwgR
Just cut your miss matched connectors off and solder in each lead.
Are we there yet????? Huh
Ex 1.6hdi van now 3 seater 1.4 multispace
Reply
#3
(09-05-2016, 06:27 PM)Tomcat3 Wrote:  You could use something like this http://www.ebay.co.uk/itm/3-WAY-PRE-WIRE...SwEetWAwgR
Just cut your miss matched connectors off and solder in each
Problem is that the femail connector on the new wiper motor is moulded into the unit unlike the old unit which could have been cut and new connectors soldered on - so the new male connector has to match the femail on the new wiper motor???? It is finding out where to obtain a new connector to mate with the Bosch wiper unit.
Reply
#4
Can you post a picture on here so we know what its got to look like. Probably your best bet is at your local breakers and cut one off a scrap car.
Are we there yet????? Huh
Ex 1.6hdi van now 3 seater 1.4 multispace
Reply
#5
(09-05-2016, 07:55 PM)Tomcat3 Wrote:  Can you post a picture on here so we know what its got to look like. Probably your best bet is at your local breakers and cut one off a scrap car.
All of the scrap yards around here closed several years ago due to Health & Safety and they are replaced with dismantlers who sell bits and bobs over the counter that they have removed themselves.  New unit like the old one is a genuine Bosch unit but the 12v 3 pin connector is built into the unit rathe than on the old unit which was on the end of about 6" of cable! Could have cut and replaced with new connectors as you described from E-Bay but now it isn't that simple...shucks....


Attached Files Thumbnail(s)
       
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Service interval notice
Last Post: jocas74
Today 02:23 AM
» Replies: 7
» Views: 359
Winter Tyres
Last Post: geoff
Today 12:19 AM
» Replies: 0
» Views: 18
23 plate Citreon Berlingo classed as a van
Last Post: W Petsa
Yesterday 10:39 PM
» Replies: 2
» Views: 36
The creation of my personal solo-travellor.
Last Post: EM58
Yesterday 06:17 PM
» Replies: 12
» Views: 740
M59 Throttle pedal
Last Post: evdama
Yesterday 01:10 PM
» Replies: 5
» Views: 178
Berlingo 2007 1.6 hdi - intermittent sticky acce...
Last Post: Romahomepete
Yesterday 01:05 PM
» Replies: 7
» Views: 329
roof rack with slats
Last Post: BigVtwin996
Yesterday 11:53 AM
» Replies: 4
» Views: 192
Battery upgrade
Last Post: evdama
27-03-2024 03:58 PM
» Replies: 0
» Views: 99
Wanted: 2003 M59 steering rack
Last Post: evdama
27-03-2024 12:45 PM
» Replies: 1
» Views: 57
Airbag Fault Code
Last Post: Cumbrian
26-03-2024 03:06 PM
» Replies: 1
» Views: 215

[-]
Recent Visitors
Locations of visitors to this page

[-]
Hosting by

QuickHostUK