Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
2010 1.6hdi - speedo fault
Just picked up a Berlingo 1.6 HDI, stupidly on test drive I didn't notice the speedo wasn't working and parted with my cash so now I'm stuck with a faulty speedo. 

Anyway I'm hoping you guys can help me, the rest of the binnacle is working fine other than the speedo and the milagage/ trip computer. 

I suspect it being a sensor but no idea where it's located and how to diagnose that's definitely the problem. 

Any info is much appreciated.
Probably faulty sensor. 
You can use "search" forum function and you will find answer in 15 min.

Best regards,
So a little update. I found the location of the speedo drive sensor (at the back of the gearbox just in front of the gear linkage rods if anyone is interested)
Replaced the old part with a new one and the speedo still isn't working.
I've checked the drive gear inside the gearbox and that moves when the wheels rotate but for some reason I'm not getting a reading on the speedo.
Had the van to the local auto electrician who had it in a Bosch computer but couldn't find any faults. I tried attaching the speedo drive to a drill and spinning it to see if the speedo registered anything but no joy.
Starting to think there's a problem in the wiring loom.

Getting really frustrated now.
Your best bet would be connecting it up to the citroen/Peugeot Lexia software and look for faults. There may be a member near you with the software who could help for beer tokens or have a look on French car forum and check out their map for Lexia user near you.
Are we there yet????? Huh
Ex 1.6hdi van now 3 seater 1.4 multispace
Uh, then you will need to check wires from sensor to BSI.

If you need schematic , shout.

Best regards,
[-] The following 1 user says Thank You to brajomobil for this post:
  • Bradjohnson
Schematic would be brilliant if you have it.

Kind regards.
Tacho, speed sensor is number 1620 on pdf page1

You have 3 wires to check
Wire 1
pin1 CM01D goes to connector 16v NR pin 2
16v NR connector is on PSF1 fuise box PDF page3  "A" picture

Wire 2
pin2 M162 goes to GROUND
Easy to check with ommmethar

Wire 3
pin3 7638  goes to connector 48V MR pin B3
48V MR connecor is on engine ECU PDF page3 "F" picture

.pdf   berlingo_speed_sensor_page1.pdf (Size: 444.21 KB / Downloads: 42)

.pdf   berlingo_speed_sensor_page2.pdf (Size: 578.63 KB / Downloads: 32)

.pdf   berlingo_speed_sensor_page3.pdf (Size: 473.01 KB / Downloads: 39)

Best regards,

Forum Jump:

Users browsing this thread: 1 Guest(s)
You have to register before you can post on our site.



(Advanced Search)

Latest Threads
09' Multispace to van conversion
Last Post: jemselectrical
Today 10:51 AM
» Replies: 57
» Views: 1889
M59 shopping trolley (modubox) bracket/shelf & t...
Last Post: benoliver999
Today 09:38 AM
» Replies: 3
» Views: 107
alternator charging voltage drop when hot 1.6 pe...
Last Post: saskak
Today 09:35 AM
» Replies: 16
» Views: 162
Wiring diagram and colour codes for offside rear...
Last Post: Romahomepete
Today 05:56 AM
» Replies: 2
» Views: 39
12v live Dash Cam
Last Post: Aussie Berlingo mk3
Today 05:11 AM
» Replies: 13
» Views: 420
Berlingo MK1 Injector seal. 1.6 HDi 2008.
Last Post: 247Dealing
Yesterday 07:33 PM
» Replies: 0
» Views: 54
Egr blanking.
Last Post: Chriz1
Yesterday 03:54 PM
» Replies: 4
» Views: 80
Clicking clutch pedal
Last Post: geoff
Yesterday 03:14 PM
» Replies: 2
» Views: 32
Diesel tank removal
Yesterday 02:20 PM
» Replies: 0
» Views: 32
Diesel tank access
Yesterday 02:06 PM
» Replies: 9
» Views: 141

Recent Visitors
Locations of visitors to this page

Hosting by