Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
2010 1.6hdi - speedo fault
#1
Just picked up a Berlingo 1.6 HDI, stupidly on test drive I didn't notice the speedo wasn't working and parted with my cash so now I'm stuck with a faulty speedo. 

Anyway I'm hoping you guys can help me, the rest of the binnacle is working fine other than the speedo and the milagage/ trip computer. 

I suspect it being a sensor but no idea where it's located and how to diagnose that's definitely the problem. 

Any info is much appreciated.
Reply
#2
Probably faulty sensor. 
You can use "search" forum function and you will find answer in 15 min.

Best regards,
brajomobil
Reply
#3
So a little update. I found the location of the speedo drive sensor (at the back of the gearbox just in front of the gear linkage rods if anyone is interested)
Replaced the old part with a new one and the speedo still isn't working.
I've checked the drive gear inside the gearbox and that moves when the wheels rotate but for some reason I'm not getting a reading on the speedo.
Had the van to the local auto electrician who had it in a Bosch computer but couldn't find any faults. I tried attaching the speedo drive to a drill and spinning it to see if the speedo registered anything but no joy.
Starting to think there's a problem in the wiring loom.

Getting really frustrated now.
Reply
#4
Your best bet would be connecting it up to the citroen/Peugeot Lexia software and look for faults. There may be a member near you with the software who could help for beer tokens or have a look on French car forum and check out their map for Lexia user near you.
Are we there yet????? Huh
Ex 1.6hdi van now 3 seater 1.4 multispace
Reply
#5
Uh, then you will need to check wires from sensor to BSI.

If you need schematic , shout.

Best regards,
brajomobil
[-] The following 1 user says Thank You to brajomobil for this post:
  • Bradjohnson
Reply
#6
Schematic would be brilliant if you have it.

Kind regards.
Reply
#7
Tacho, speed sensor is number 1620 on pdf page1


You have 3 wires to check
Wire 1
pin1 CM01D goes to connector 16v NR pin 2
16v NR connector is on PSF1 fuise box PDF page3  "A" picture


Wire 2
pin2 M162 goes to GROUND
Easy to check with ommmethar


Wire 3
pin3 7638  goes to connector 48V MR pin B3
48V MR connecor is on engine ECU PDF page3 "F" picture


.pdf   berlingo_speed_sensor_page1.pdf (Size: 444.21 KB / Downloads: 42)

.pdf   berlingo_speed_sensor_page2.pdf (Size: 578.63 KB / Downloads: 32)

.pdf   berlingo_speed_sensor_page3.pdf (Size: 473.01 KB / Downloads: 39)

Best regards,
brajomobil
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
CPLAY2air wireless adapter for factory CarPlay
Last Post: boop
Yesterday 10:47 PM
» Replies: 24
» Views: 4666
Greetings!
Last Post: Matt Haigh
Yesterday 10:25 PM
» Replies: 2
» Views: 39
Modutop/Zenith - which years? MPG?
Last Post: badgerjockey
Yesterday 09:22 PM
» Replies: 0
» Views: 21
Eolys fault
Last Post: Jimbobey
Yesterday 08:21 PM
» Replies: 5
» Views: 89
Brake fluid check
Last Post: notsofast
Yesterday 08:06 PM
» Replies: 2
» Views: 44
Retro fit cruise meltdown
Last Post: Zion
Yesterday 07:26 PM
» Replies: 11
» Views: 150
White van man
Last Post: Zion
Yesterday 03:38 PM
» Replies: 1
» Views: 45
Delivery times..... for 2021
Last Post: samefredd
Yesterday 02:27 PM
» Replies: 56
» Views: 22653
were and how do i find pcv breather
Last Post: oilyrag
Yesterday 10:03 AM
» Replies: 10
» Views: 120
Today's mystery object to fall off the Berlingo
Last Post: Kieron G
23-06-2022 10:25 PM
» Replies: 13
» Views: 18007

[-]
Recent Visitors
Locations of visitors to this page

[-]
Hosting by

QuickHostUK