Thread Rating:
  • 25 Vote(s) - 3.56 Average
  • 1
  • 2
  • 3
  • 4
  • 5
tow hitch points
#1
hi im going to make up a tow hitch for my 07 berlingo 1.6

looked at the net picts of the tow bar and it looks like

[Image: a1-bar12562944504ae188325ea7c.jpg]

looked under the van but where are the 3 holes either side?

cant see any holes at all
Reply
#2
Drill those holes.
Reply
#3
so is there no standard mounting points from factory?

where in the 2" rails that run down either side of the spare wheel?

Reply
#4
Hi and welcome to the forum corkgsxr. If you are going to stick around (and please do) then when you've got a couple of minutes, put a post in the "intro" or "owners" areas to say hello and introduce yourself (and your Berlingo). Cheers
2005 Berlingo Multispace 1.6i Desire (Iron Grey)

If everything seems to be going well, you have obviously overlooked something.


Reply
#5
Welcome corkgsxr to Berlingo forum.

May I draw your attention to this information copied from the Departmant For Transport website and I quote,

"4. What are the requirements to fit a type approved tow bar?

If you wish to tow anything with a car which was first used on or after the 1st August 1998 the car must be fitted with a type approved tow bar.

5. My car was first registered on 1st September 1998; do I need a Type approved tow bar?

Yes, all cars first registered on or after 1st August 1998 must be fitted with a type approved tow bar if they are to be used for towing.

6. How can I tell if a tow bar is type approved?

Each type approved tow bar will have a label, plate, or stamping detailing its type approval number for example E11xxxxxxx, and the details of the vehicle for which it is an approved fitment.

7. May I fit a type approved tow bar myself?

Yes provided you use the car manufacturer's approved mounting points, and follow the tow bar manufacturer's instructions."

So clearly, the home manufacture of towbars is no longer permitted, I have recently had a Witter towbar fitted to my vehicle, this is type-approved and all holes matched up with ready drilled ones in the chassis.

I am not in any way doubting your ability to fabricate and weld materials but just pointing out that laws have changed and in the event of an accident then not only do you risk the attention of the police but also you would undoubtedly invalidate your insurance.

http://www.dft.gov.uk/pgr/roads/vehicles...uently4577

To make you further aware, towbars now form part of the current annual M.O.T. test for vehicles in the United Kingdom


Berlingo Multispace 2.0HDI '54 reg Mediterranean Blue
Reply
#6
fair point but i just dont have the dosh to be buying one

made the last one for my transit never had a bother.

all im wondering is where the manufacturer holes for mounting the bar to are?

im going to fab one up i have all the stuff i need just cant find the holes. Dodgy

im in ireland so its a diff test, and i know no tester over here will fail my bars.

even after the new legislation that was to fail all aftermarket exhausts came in any i done still passed as the were welded properly and no stupid loud one at funny angles
Reply
#7
I have done the same myself and in the past have made, modified and welded towbars but I can no longer get my materials at the right price (Does help to have worked in engineering, nudge nudge) and I am debarred from doing any type of electric welding due to having an implanted cardiac defibrillator which is sensitive to powerful electric currents.

Good luck
Berlingo Multispace 2.0HDI '54 reg Mediterranean Blue
Reply
#8
its the defib of be the most worryed about with welding, best be carefull with that

i have everything needed here the only thing i need is the socket but ill get that when alls made, im a plumber but iv been welding since i was 15

and im fairly good a wiring too
Reply
#9
Hi Corkgsxr. Welcome to forum.
See in attach how original tow bar and tow ball should be mount.
I think this will help you.


Attached Files
.pdf   672.pdf (Size: 879.09 KB / Downloads: 61)
[-] The following 1 user says Thank You to pk7478 for this post:
  • corkgsxr
Reply
#10
thanks the picts helped greatly

i saw those holes in the chassis do you have to drill them out?

ill take picts after i weld one up
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Fozen touch screen
Last Post: Colin McLachlan
Today 11:08 AM
» Replies: 0
» Views: 13
23 plate Citreon Berlingo classed as a van
Last Post: evdama
Today 09:17 AM
» Replies: 3
» Views: 58
Service interval notice
Last Post: evdama
Today 09:06 AM
» Replies: 8
» Views: 383
Winter Tyres
Last Post: evdama
Today 09:03 AM
» Replies: 1
» Views: 47
The creation of my personal solo-travellor.
Last Post: EM58
Yesterday 06:17 PM
» Replies: 12
» Views: 748
M59 Throttle pedal
Last Post: evdama
Yesterday 01:10 PM
» Replies: 5
» Views: 188
Berlingo 2007 1.6 hdi - intermittent sticky acce...
Last Post: Romahomepete
Yesterday 01:05 PM
» Replies: 7
» Views: 333
roof rack with slats
Last Post: BigVtwin996
Yesterday 11:53 AM
» Replies: 4
» Views: 198
Battery upgrade
Last Post: evdama
27-03-2024 03:58 PM
» Replies: 0
» Views: 107
Wanted: 2003 M59 steering rack
Last Post: evdama
27-03-2024 12:45 PM
» Replies: 1
» Views: 60

[-]
Recent Visitors
Locations of visitors to this page

[-]
Hosting by

QuickHostUK