Thread Rating:
  • 13 Vote(s) - 3.69 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Key fob programming help
#1
I've recently bought a spare key for an '05 multispace but the remote central locking doesn't work with it.

I've read around and there's a few guides on how to program it to work but no matter what I try the new key just won't bind. All instructions I've found say you need to repeat the steps for each fob but I've deliberately not done the steps for the old fob and it still works so I'm guessing it's not even going into programming mode.

Any ideas on exactly what the correct procedure should be? Or can this only be done with a lexia 3?
Reply
#2
Have a read of this. Confusedtudy: Confusedalut:

.pdf   key fob syncing2.pdf (Size: 12.65 KB / Downloads: 774)
2006 2.0hdi 600 with bench seat.  Cool
[-] The following 3 users say Thank You to Rustscrat for this post:
  • Ol'Jeffers, RolyG, ron
Reply
#3
Thanks for this post.
Reply
#4
let's try
Reply
#5
My remote key didn't seem to work, when I opened it up the microswitch had come off. New one bought for £1.50 and soldered on in seconds and all working properly now!!
Reply
#6
(19-10-2013, 08:46 PM)Waynejohnson Wrote:  My remote key didn't seem to work, when I opened it up the microswitch had come off. New one bought for £1.50 and soldered on in seconds and all working properly now!!

Which microswitch was that?
The Older I get the Better I Was!  Cool
Reply
#7
Similar (I think) problem for me. New key fob, put existing transponder inside, remote lock/unlock works but engine won't start. Hopefully now I've posted I can download the above instructions...

Wink
Reply
#8
Thectransponder is probably too far away from the sensor.

Have you tried removing transponder placing next to sensor and then trying to start the car,?
Reply
#9
Fixed - problem mainly due to me being an idiot. I'd transferred a new key to the new fob, plus the original circuit board. What I hadn't swapped was the little black transponder from the corner. Once I swapped that too everything then worked.

Ta for the advice though!
Reply
#10
Hi sorry to drag up an old post but i need to post a reply to download the document, i recently bought a second hand key fob from ebay for my berlingo, i swapped the back over and it starts but cant get the fob to program to the car, the circuit board inside does look different to the old one, will the different type still be compatible?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
23 plate Citreon Berlingo classed as a van
Last Post: evdama
Today 09:17 AM
» Replies: 3
» Views: 49
Service interval notice
Last Post: evdama
Today 09:06 AM
» Replies: 8
» Views: 378
Winter Tyres
Last Post: evdama
Today 09:03 AM
» Replies: 1
» Views: 43
The creation of my personal solo-travellor.
Last Post: EM58
Yesterday 06:17 PM
» Replies: 12
» Views: 748
M59 Throttle pedal
Last Post: evdama
Yesterday 01:10 PM
» Replies: 5
» Views: 187
Berlingo 2007 1.6 hdi - intermittent sticky acce...
Last Post: Romahomepete
Yesterday 01:05 PM
» Replies: 7
» Views: 333
roof rack with slats
Last Post: BigVtwin996
Yesterday 11:53 AM
» Replies: 4
» Views: 196
Battery upgrade
Last Post: evdama
27-03-2024 03:58 PM
» Replies: 0
» Views: 105
Wanted: 2003 M59 steering rack
Last Post: evdama
27-03-2024 12:45 PM
» Replies: 1
» Views: 60
Airbag Fault Code
Last Post: Cumbrian
26-03-2024 03:06 PM
» Replies: 1
» Views: 219

[-]
Recent Visitors
Locations of visitors to this page

[-]
Hosting by

QuickHostUK